The breakdown of polymer-based restorative materials is often due to a combination of chemical and physical stresses that cause wear. Presently, the most reliable predictor of clinical wear behavior is the well-planned clinical study. Although it is possible in some cases to correlate the results of such studies with an in-vitro test, such correlations do not always provide a sound scientific basis for predicting wear. It is believed that fatigue induced wear is an important phenomenon in the degradation of some restorative materials, particularly the """"""""microfilled"""""""" composites, when used in a stress-bearing situation. This is relatively neglected area of restorative materials research. Several novel approaches will be employed in this study in order to arrive at an understanding of fatigue-induced wear of polymer materials used in restorative dentistry. A series of resin materials similar to those presently used as matrix resins for dental composites will be prepared by an industrial contractor. Some samples will be filled with low amounts of silanated colloidal silica, as is done in practice to control the viscosity of matrix materials. All samples will be characterized with respect to degree of cure and Tg. Pin- on-disc wear testing will utilize an appropriate stylus geometry to induce subsurface fatigue wear. Dynamic tensile and shear fatigue testing will be done following relevant ASTM specifications. Employing the properties thus measured, finite element modeling techniques will be used to mimic pin-on- disc wear behavior. Finally, fatigue fracture surfaces, wear surfaces, and wear debris will be characterized using classical and fractal geometric methods.

Agency
National Institute of Health (NIH)
Institute
National Institute of Dental & Craniofacial Research (NIDCR)
Type
Research Project (R01)
Project #
5R01DE009530-03
Application #
3223284
Study Section
Oral Biology and Medicine Subcommittee 1 (OBM)
Project Start
1990-07-01
Project End
1994-06-30
Budget Start
1992-07-01
Budget End
1993-06-30
Support Year
3
Fiscal Year
1992
Total Cost
Indirect Cost
Name
Temple University
Department
Type
Schools of Dentistry
DUNS #
City
Philadelphia
State
PA
Country
United States
Zip Code
19122
Wang, Wenhai; Sadeghipour, Keya; Baran, George (2008) Finite element analysis of the effect of an interphase on toughening of a particle reinforced polymer composite. Compos Part A Appl Sci Manuf 39:956-964
Debnath, S; Ranade, R; Wunder, S L et al. (2004) Interface effects on mechanical properties of particle-reinforced composites. Dent Mater 20:677-86
Debnath, Subir; Wunder, Stephanie L; McCool, John I et al. (2003) Silane treatment effects on glass/resin interfacial shear strengths. Dent Mater 19:441-8
Liu, Q; Ding, J; Chambers, D E et al. (2001) Filler-coupling agent-matrix interactions in silica/polymethylmethacrylate composites. J Biomed Mater Res 57:384-93
Baran, G; Boberick, K; McCool, J (2001) Fatigue of restorative materials. Crit Rev Oral Biol Med 12:350-60
McCool, J I; Boberick, K G; Baran, G R (2001) Lifetime predictions for resin-based composites using cyclic and dynamic fatigue. J Biomed Mater Res 58:247-53
Yarovoy, Y K; Baran, G; Wunder, S L et al. (2000) Submicron-size particles of ultrahigh molecular weight polyethylene produced via nonsolvent and temperature-induced crystallization. J Biomed Mater Res 53:152-60
Baran, G R; McCool, J I; Boberick, K G et al. (1999) Size effect in resin/glass composite flexure strengths. J Oral Rehabil 26:775-80
Baran, G R; McCool, J I; Paul, D et al. (1998) Weibull models of fracture strengths and fatigue behavior of dental resins in flexure and shear. J Biomed Mater Res 43:226-33
Baran, G; Sadeghipour, K; Jayaraman, S et al. (1998) Crack propagation directions in unfilled resins. J Dent Res 77:1864-73

Showing the most recent 10 out of 13 publications