The purpose of this project is to investigate a novel completely bioresorbable integrated structural/delivery scaffold for controlled BMP2 delivery in cervical spine fusion. Over 230,000 cervical spine fusions were performed in the US alone in 2008, accounting for 41% of all spine fusions. Due to enhanced clinical outcomes in lumbar spine fusion while simultaneously eliminating the need for graft harvest, off label usage increased significantly in cervical spine fusion. However, severe adverse effects including death were associated with BMP2 usage in cervical spine fusion, prompting the FDA to warn against BMP2 use in cervical spine fusion, as reported by the New York Times and Wall Street Journal. It is widely hypothesized that these adverse effects are due to high BMP2 dosages, poor BMP2 retention and uncontrolled BMP2 release by the currently approved collagen sponge carrier that allows BMP2 diffusion into surrounding soft tissues, with associated increased vascular edema and ectopic bone formation. Our laboratory has developed technology integrating topology optimization, bioresorbable polymer solid free-form fabrication, BMP2 conjugation, and bioresorbable fixation to develop a new structural/delivery system for cervical spine fusion. We will engineer this new structural/delivery system and test the delivery of BMP2 in a large pre-clinical (pig) animal model of cervical spine fusion. We hypothesize that topology optimized integrated porous structural carriers with surface area and mechanical modulus close to vertebral trabecular bone and a permeability greater than 10-8 m4/Ns conjugated with lower than clinical dosages (0.5 mg) of BMP2 will provide superior fusion in terms of time to fusion, and fusion mass volume and stiffness compared to current clinical cervical cage designs delivering BMP2 via conjugation or FDA approved collagen sponge. We will test this hypothesis by comparing optimized and clinical cage designs alone, with conjugated BMP2 delivery and with collagen sponge delivery. These experimental groups will allow us to specifically test if the new system provides both better load carrying distribution as well as better controlled bone formation using a different BMP2 delivery method. Successful completion of this proposal will provide a new paradigm for bioresorbable fusion systems in the cervical spine, achieving spinal fusion with lower, safer, and less expensive doses of BMP2.

Public Health Relevance

This proposal aims to develop an integrated structural BMP2 delivery vehicle that is optimized for mechanical load bearing and BMP2 delivery simultaneously. The project is designed to test our hypothesis that this integrated structural carrier can provide a safer, more effective, lower cost cervical fusion device by more efficaciously delivering BMP2. Specifically, we hypothesize that this device designed using topology optimization methods can provide superior fusion outcomes in terms of reduced subsidence, more localized bone formation, and mechanical stability than traditional box fusion cage designs delivering BMP2 via collagen sponges.

Agency
National Institute of Health (NIH)
Institute
National Institute of Arthritis and Musculoskeletal and Skin Diseases (NIAMS)
Type
Research Project (R01)
Project #
1R01AR060892-01A1
Application #
8239266
Study Section
Musculoskeletal Tissue Engineering Study Section (MTE)
Program Officer
Panagis, James S
Project Start
2011-09-17
Project End
2015-08-31
Budget Start
2011-09-17
Budget End
2012-08-31
Support Year
1
Fiscal Year
2011
Total Cost
$520,253
Indirect Cost
Name
University of Michigan Ann Arbor
Department
Biomedical Engineering
Type
Schools of Engineering
DUNS #
073133571
City
Ann Arbor
State
MI
Country
United States
Zip Code
48109
Knutsen, Ashleen R; Borkowski, Sean L; Ebramzadeh, Edward et al. (2015) Static and dynamic fatigue behavior of topology designed and conventional 3D printed bioresorbable PCL cervical interbody fusion devices. J Mech Behav Biomed Mater 49:332-42
Hollister, Scott J; Flanagan, Colleen L; Zopf, David A et al. (2015) Design control for clinical translation of 3D printed modular scaffolds. Ann Biomed Eng 43:774-86
Patel, Janki Jayesh; Modes, Jane E; Flanagan, Colleen L et al. (2015) Dual Delivery of EPO and BMP2 from a Novel Modular Poly-?-Caprolactone Construct to Increase the Bone Formation in Prefabricated Bone Flaps. Tissue Eng Part C Methods 21:889-97
Patel, Janki J; Flanagan, Colleen L; Hollister, Scott J (2015) Bone Morphogenetic Protein-2 Adsorption onto Poly-?-caprolactone Better Preserves Bioactivity In Vitro and Produces More Bone In Vivo than Conjugation Under Clinically Relevant Loading Scenarios. Tissue Eng Part C Methods 21:489-98