As many as 1.2 million Americans rely on wheelchairs for mobility, and this number is increasing. Even though upper extremity (UE) musculoskeletal problems are common among wheelchair users, the scientific literature on the biomechanics of wheelchair propulsion is limited. In particular, the relationship between upper extremity loads and the risk of musculoskeletal injury is poorly understood. A systematic evaluation of the loads on the upper extremities of wheelchair users will do much to improve our understanding, treatment and ability to prevent musculoskeletal injuries in this population. In this study the investigators will use experimental techniques that they have developed and validated in conjunction with an analytical model of wheelchair propulsion that they have already developed. This combination will allow them to predict the maximum propulsion moment about the wheel axle for a given wheelchair configuration as a function of a subject's anthropometric dimensions and strength capacities at the shoulder, elbow, and wrist joints. In this study, the investigators propose to examine the effects of seat position and handrim diameter on the mechanics of wheelchair propulsion. In particular, three measures of wheelchair propulsion effectiveness will be used. These measures include the wheelchair propulsion strength ratio (WPSR), the fraction effective force (FEF), and the propulsion moment generated about the wheel axle (Mw). Each of these quantities has potential importance and will be analyzed while subjects propel a wheelchair on level ground and up a 12:1 (run: rise) ramp to address the following specific aims and hypotheses: Hypotheses 1 - The seat height will be """"""""optimal"""""""" (i.e., minimum WPSR; maximum FEF and Mw) when the elbow angle is 120 degrees (180 degrees=full elbow extension) with the hands is at the top-dead center of the handrim, (as contrasted to angles of 100 degrees and 140 degrees.) Hypothesis 2 - The neutral position of the axle (2.5cm forward of the most extreme posterior position) will be more optimal that the most posterior or anterior positions (i.e., minimum WPSR; maximum FEF and Mw). Hypothesis 3 - With the axle in the neutral position and the seat providing the optimal elbow angle, a medium handrim diameter (40cm) will be a better choice as compared to smaller (28cm) and larger (51cm) rim diameters (i.e., minimum WPSR; maximum FEF and Mw).

Agency
National Institute of Health (NIH)
Institute
Eunice Kennedy Shriver National Institute of Child Health & Human Development (NICHD)
Type
Research Project (R01)
Project #
5R01HD033806-06
Application #
6520980
Study Section
Geriatrics and Rehabilitation Medicine (GRM)
Program Officer
Quatrano, Louis A
Project Start
1996-08-01
Project End
2004-05-31
Budget Start
2002-06-01
Budget End
2004-05-31
Support Year
6
Fiscal Year
2002
Total Cost
$190,485
Indirect Cost
Name
Mayo Clinic, Rochester
Department
Type
DUNS #
City
Rochester
State
MN
Country
United States
Zip Code
55905
Sabick, Michelle B; Kotajarvi, Brian R; An, Kai-Nan (2004) A new method to quantify demand on the upper extremity during manual wheelchair propulsion. Arch Phys Med Rehabil 85:1151-9
Lin, Hwai-Ting; Su, Fong-Chin; Wu, Hong-Wen et al. (2004) Muscle forces analysis in the shoulder mechanism during wheelchair propulsion. Proc Inst Mech Eng H 218:213-21
Kotajarvi, Brian R; Sabick, Michelle B; An, Kai-Nan et al. (2004) The effect of seat position on wheelchair propulsion biomechanics. J Rehabil Res Dev 41:403-14
Morrow, D A; Guo, L Y; Zhao, K D et al. (2003) A 2-D model of wheelchair propulsion. Disabil Rehabil 25:192-6
Guo, Lan-Yuen; Zhao, K D; Su, Fong-Chin et al. (2003) Moment generation in wheelchair propulsion. Proc Inst Mech Eng H 217:405-13
Kotajarvi, Brian R; Basford, Jeffrey R; An, Kai-Nan (2002) Upper-extremity torque production in men with paraplegia who use wheelchairs. Arch Phys Med Rehabil 83:441-6
Sabick, M B; Zhao, K D; An, K N (2001) A comparison of methods to compute the point of force application in handrim wheelchair propulsion: a technical note. J Rehabil Res Dev 38:57-68
Wu, H W; Berglund, L J; Su, F C et al. (1998) An instrumented wheel for kinetic analysis of wheelchair propulsion. J Biomech Eng 120:533-5