X-ray fluoroscopy provides a combination of real-time imaging, high spatial resolution, ease of use, and device compatibility that is essential for rapid diagnosis of coronary artery disease and catheter guidance during fluoroscopically-guided interventional (FGI) procedures. Although the millions of FGI procedures performed in the U.S. each year undeniably improve and save lives, these procedures entail a radiation burden on both the patient and the medical staff who perform them. Radiation risks include serious skin injury, cataracts, and cancer. Unfortunately, there is limited room for improvement in the dose efficiency of conventional x-ray systems. The 2D projection format of conventional fluoroscopy also fails to provide the 3D device and anatomic information needed for modern catheter ablation procedures. The goal of this project is to develop a novel inverse-geometry x-ray fluoroscopic system that will dramatically reduce x-ray dose to patient and staff, while simultaneously providing real-time 3D catheter guidance. The Scanning-Beam Digital X-ray (SBDX) system is a low-dose fluoroscopic/fluorographic system that performs 30 frame/sec imaging using low-scatter inverse-geometry scanning. Previous NIH-funded research enabled the construction of an advanced SBDX system capable of reducing patient entrance skin dose to 15% of a conventional dose while maintaining 100% of conventional image signal-to-noise ratio. This research also yielded two new interventional techniques that exploit the unique SBDX real-time, multiplane, tomosynthetic reconstructor: frame-by-frame 3D catheter tip tracking and calibration-free 3D vessel analysis for device sizing. This new proposal will advance SBDX into the interventional laboratory through three projects. First, a human subjects study will be performed to compare SBDX and conventional x-ray dose, image quality, and interventional device sizing accuracy. Second, a procedure-room system for 3D catheter tracking and cardiac visualization will be constructed and validated in an animal model of ablation in the left atrium. Third, the ability to perform SBDX computed tomography in the interventional room will be developed, in order to provide 3D cardiac maps for ablation procedures without the need for a separate, pre-procedure CT scan. Reducing x-ray dose in the cardiac cath lab is critical to maximizing the safety of patient and staff. Real-time three-dimensional imaging capability is needed for many modern interventional procedures. The successful conclusion of this research will be a low dose x-ray fluoroscopic system which provides clinical image quality, novel therapeutic tools, and 3D imaging capability in a single interventional laboratory.

Public Health Relevance

Coronary artery disease and cardiac arrhythmia are significant causes of morbidity and mortality in our society. Over 1,000,000 coronary angioplasties and 200,000 catheter ablation procedures for the treatment of atrial fibrillation are performed annually in our country, saving many lives and improving the quality of many more. Successful completion of this work will provide therapeutic tools which improve the outcomes of these procedures, while dramatically lowering the radiation exposure to the patient and medical staff.

Agency
National Institute of Health (NIH)
Institute
National Heart, Lung, and Blood Institute (NHLBI)
Type
Research Project (R01)
Project #
5R01HL084022-08
Application #
8780662
Study Section
Special Emphasis Panel (ZRG1-BMIT-J (01))
Program Officer
Buxton, Denis B
Project Start
2006-04-01
Project End
2015-12-31
Budget Start
2015-01-01
Budget End
2015-12-31
Support Year
8
Fiscal Year
2015
Total Cost
$553,245
Indirect Cost
$125,060
Name
University of Wisconsin Madison
Department
Internal Medicine/Medicine
Type
Schools of Medicine
DUNS #
161202122
City
Madison
State
WI
Country
United States
Zip Code
53715
Dunkerley, David A P; Slagowski, Jordan M; Bodart, Lindsay E et al. (2017) Automated 3D coronary sinus catheter detection using a scanning-beam digital x-ray system. Proc SPIE Int Soc Opt Eng 10132:
Dunkerley, David A P; Slagowski, Jordan M; Funk, Tobias et al. (2017) Dynamic electronic collimation method for 3-D catheter tracking on a scanning-beam digital x-ray system. J Med Imaging (Bellingham) 4:023501
Speidel, Michael A; Slagowski, Jordan M; Dunkerley, David A P et al. (2017) Localization of cardiac volume and patient features in inverse geometry x-ray fluoroscopy. Proc SPIE Int Soc Opt Eng 10132:
Slagowski, Jordan M; Dunkerley, David A P; Hatt, Charles R et al. (2017) Single-view geometric calibration for C-arm inverse geometry CT. J Med Imaging (Bellingham) 4:013506
Buehler, Marc; Slagowski, Jordan M; Mistretta, Charles A et al. (2017) 4D DSA reconstruction using tomosynthesis projections. Proc SPIE Int Soc Opt Eng 10132:
Slagowski, Jordan M; Dunkerley, David A P; Hatt, Charles R et al. (2016) A geometric calibration method for inverse geometry computed tomography using P-matrices. Proc SPIE Int Soc Opt Eng 9783:
Hatt, Charles R; Wagner, Martin; Raval, Amish N et al. (2016) Dynamic tracking of prosthetic valve motion and deformation from bi-plane x-ray views: feasibility study. Proc SPIE Int Soc Opt Eng 9786:
Dunkerley, David A P; Funk, Tobias; Speidel, Michael A (2016) Method for dose-reduced 3D catheter tracking on a scanning-beam digital x-ray system using dynamic electronic collimation. Proc SPIE Int Soc Opt Eng 9783:
Hatt, Charles R; Speidel, Michael A; Raval, Amish N (2016) Real-time pose estimation of devices from x-ray images: Application to x-ray/echo registration for cardiac interventions. Med Image Anal 34:101-108
Slagowski, Jordan M; Tomkowiak, Michael T; Dunkerley, David A P et al. (2015) Feasibility of CT-based 3D anatomic mapping with a scanning-beam digital x-ray (SBDX) system. Proc SPIE Int Soc Opt Eng 9412:

Showing the most recent 10 out of 22 publications